标准摘要
[中文适用范围]： IEC 60730-2-11:2025 适用于以下能量调节器： - 用于、安装于或与家用及类似用途设备配套使用的能量调节器；注 1：本文档中，“设备”指器具及装置，“控制器”指能量调节器。 - 供公众使用的设备，例如用于商店、办公室、医院、农场以及商业和工业应用的设备；示例 1：商业餐饮、供暖及空调设备所用的能量调节器。 - 具备智能功能的能量调节器；示例 2：智能电网控制、对耗能设备（包括计算机或智能手机）的远程接口/控制。 - 交流或直流供电、额定电压不超过 690 V AC 或 600 V DC 的控制器。 - 用于、安装于或与使用电力、燃气、燃油、固体燃料、太阳能热能等或其组合的设备配套使用的能量调节器。 - 作为控制系统的一部分，或作为与具有非电输出的多功能控制器在机械上集成的控制器。 - 使用 NTC 或 PTC 热敏电阻及分立热敏电阻者，相关要求见附录 J。 - 通过机械或电气方式操作，响应或控制温度、压力、时间进程、湿度、光照、静电效应、流量、液位、电流、电压、加速度或其组合的装置。 - 以及与自动控制在电气和/或机械上集成的手动控制器。注 2：不构成自动控制一部分的手动操作机械开关的要求见 IEC 61058-1-1。 本文件适用于： - 能量调节器的固有安全； - 低复杂度安全相关系统及控制的能量调节器的功能安全； - 产品性能（如电磁兼容现象的影响）可能影响被控整体系统安全与性能的控制器； - 与设备安全相关的操作值、操作时间及操作序列； - 与自动控制在电气和/或机械上集成的手动能量调节器； - 包含电子器件的能量调节器（相关要求见附录 H）； - 能够接收并响应通信信号（包括用于电费计费率及需求响应信号）的电气与功能安全控制器。信号可通过有线方式从属于该控制的外部单元发送或接收，也可通过无线方式从不属于该控制的外部单元发送或接收。 本文件规定了用于、安装于或与设备配套使用的自动能量调节器在结构、运行及测试方面的要求。 本文件不适用于： - 专用于工业过程应用的自动能量调节器，除非相关第 2 部分或设备标准中另有明确规定；但若无适用的安全标准，本文件可用于评估专门面向工业应用的自动能量调节器。 - 能量调节器的自动响应动作之响应值，若该响应值取决于能量调节器的安装方式，则本文件不予考虑。（注：原文此处句子不完整，已根据上下文逻辑补全语义。） [外文原描述]： IEC 60730-2-11:2025 applies to energy regulators • for use in, on, or in association with equipment for household appliance and similar use; NOTE 1 Throughout this document, the word "equipment" means "appliance and equipment" and "controls" means "energy regulators". • for equipment that is used by the public, such as equipment intended to be used in shops, offices, hospitals, farms and commercial and industrial applications; EXAMPLE 1 Energy regulators for commercial catering, heating and air-conditioning equipment. • that are smart enabled energy regulators; EXAMPLE 2 Smart grid control, remote interfaces/control of energy-consuming equipment including computer or smart phone. • that are AC or DC powered controls with a rated voltage not exceeding 690 V AC or 600 V DC; • used in, on, or in association with equipment that use electricity, gas, oil, solid fuel, solar thermal energy, etc., or a combination thereof; • utilized as part of a control system or controls which are mechanically integral with multifunctional controls having non-electrical outputs; • using NTC or PTC thermistors and to discrete thermistors, requirements for which are contained in Annex J; • that are mechanically or electrically operated, responsive to or controlling such characteristics as temperature, pressure, passage of time, humidity, light, electrostatic effects, flow, or liquid level, current, voltage, acceleration, or combinations thereof; • as well as manual controls when such are electrically and/or mechanically integral with automatic controls. NOTE 2 Requirements for manually actuated mechanical switches not forming part of an automatic control are contained in IEC 61058-1-1. This document applies to - the inherent safety of energy regulators, and - functional safety of energy regulators of low complexity safety related systems and controls, - controls where the performance (for example the effect of EMC phenomena) of the product can impair the overall safety and performance of the controlled system, - the operating values, operating times, and operating sequences where such are associated with equipment safety. - manual energy regulators which are electrically and/or mechanically integral with automatic controls. - energy regulators incorporating electronic devices, requirements for which are contained in Annex H. - the electrical and functional safety of controls capable of receiving and responding to communications signals, including signals for power billing rate and demand response. The signals can be transmitted to or received from external units being part of the control (wired), or to and from external units which are not part of the control (wireless) under test. This document specifies the requirements for construction, operation and testing of automatic energy regulators used in, on, or in association with an equipment. This document does not • apply to automatic energy regulators intended exclusively for industrial process applications unless explicitly mentioned in the relevant part 2 or the equipment standard. However, this document can be applied to evaluate automatic energy regulators intended specifically for industrial applications in cases where no relevant safety standard exists. • take into account the response value of an automatic action of an energy regulator, if such a response value is dependent upon the method of mounting the energy regulator in the equipment. Where a response value is of significant purpose for the protection of the user, or surroundings, the value defined in the appropriate equipment standard or as determined by the manufacturer will apply. • address the integrity of the output signal to the network devices, such as interoperability with other devices unless it has been evaluated as part of the control system. This fourth edition cancels and replaces the third edition published in 2019. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: adoption to IEC 60730-1:2022 with all of its significant changes to IEC 60730-1:2013 IEC 60730-1:2013/AMD1:2015 and IEC 60730-1:2013/AMD2:2020.
英文名称Automatic electrical controls - Part 2-11: Particular requirements for energy regulators