可调速电力驱动系统 - 第2部分:一般要求 - 低压可调频率a.c.的额定规范 动力驱动系统

[中文适用范围]： IEC 61800-2 适用于包括半导体功率转换及其控制、保护、监控、测量和电动机在内的可调速交流电力驱动系统。该标准适用于旨在向交流电机供电、额定转换器输入电压（线电压）高达1000 V交流电、50 Hz或60 Hz，且/或直流输入侧电压高达1500 V的可调速电力驱动系统。不适用于牵引应用和电动汽车。本部分旨在定义交流电力驱动系统（PDS）的以下方面：PDS的主要部分、额定值和性能、PDS安装和运行环境规范、以及在指定完整PDS时可能适用的其他规范。 [外文原描述]： IEC 61800-2:2015 applies to adjustable speed electric a.c. power drive systems, which include semiconductor power conversion and the means for their control, protection, monitoring, measurement and the a.c. motors. It applies to adjustable speed electric power drive systems intended to feed a.c. motors from a BDM connected to line-to-line voltages up to and including 1 kV a.c. 50 Hz or 60 Hz and/or voltages up to and including 1,5 kV d.c. input side. NOTE 1 Adjustable speed electric a.c. power drive systems intended to feed a.c. motors, and with rated converter input voltages above 1 000 V a.c. are covered by IEC 61800-4. NOTE 2 Adjustable speed electric d.c. power drive systems intended to feed d.c. motors are covered by IEC 61800-1. NOTE 3 For adjustable speed electric a.c. power drive systems having series-connected electronic power converter sections, the line-to-line voltage is the sum of the series connected input voltages. Traction applications and electric vehicles are excluded from the scope of this standard. IEC 61800-2:2015 is intended to define the following aspects of an a.c. power drive system (PDS): - principal parts of the PDS; - ratings and performance; - specifications for the environment in which the PDS is intended to be installed and operated; - other specifications which might be applicable when specifying a complete PDS. This standard provides minimum requirements, which may be used for the development of a specification between customer and manufacturer. This edition includes the following significant technical changes with respect to the previous edition. a) Clause 1 (Scope) has been updated, b) Clause 2 (Normative references) has been updated, c) Clause 3 (Definitions) has been updated including fundamental definitions to be used across the IEC 61800 series of standards, d) Clause 4 has been updated with respect to: 1) description of the basic topology for BDM/CDM/PDS (4.2); 2) ratings and performance (4.3 and 4.4); 3) reference to applicable standards within the IEC 61800 series with respect to EMC (IEC 61800-3), Electrical safety (IEC 61800-5-1), Functional safety (IEC 61800-5-2), Load duty aspects (IEC TR 61800-6), Communication profiles (IEC 61800-7 series) and Power interface voltage (IEC TS 61800-8) to avoid conflicting requirements (4.5, 4.6, 4.7, 4.10, 4.11, 4.12); 4) update of requirement for ECO design (4.8); 5) update of requirement for environmental evaluation (4.9); 6) implementation of requirement for explosive atmosphere (4.13). e) Clause 5 has been updated with test requirement in order to provide a clear link between design requirement and test requirement. f) Clause 6 has been updated to harmonize the marking and documentation requirement within the IEC 61800 series. g) Existing Annexes A to G have been deleted and replaced with new Annexes A to C.