液压传动.16MPa（160bar）紧凑型系列单杆液压缸附件的安装尺寸

[中文适用范围]： 本文件规定了符合 ISO 6020-2 的 16 MPa (160 bar) 紧凑型气缸附件互换性所需的安装尺寸。 这些附件专为与按照 ISO 6020-2 制造的气缸配合使用而设计，但这并不限制其应用1)。 本文件涵盖以下根据 ISO 6099 确定的附件： ——AP6 — 球形杆眼、内螺纹（见图 1 和表 1）； ——AB5——U形支架，球眼，角度（见图2和表2）； ——AA6-L——枢轴销、球面轴承、锁定板（见图3和表3）； ——AL6——枢轴销锁紧板（见图4和表4）； ——AP2——U形杆，内螺纹（见图5和表5）； ——AP4——杆眼普通、内螺纹（见图6和表6）； ——AB2——吊环支架（见图7和表7）； ——AB4——U形夹支架，直型（见图8和表8）； ——AA4-S — 普通枢轴销（开口销）（见图 9 和表 9）； ——AA4-R — 枢轴销，普通（环）（见图 10 和表 10）； ——AT4 — 耳轴支架（参见图 11 和表 11）。 这些附件用于液压缸上，用于机械地传递缸力。 这些附件的设计基于 ISO 3320 和 ISO 2944 规定的气缸内径和压力产生的最大力。 本文件仅适用于按照本文件制造的产品的尺寸标准；它不适用于它们的功能特性。 [外文原描述]： This document specifies the mounting dimensions required for interchangeability of accessories for 16 MPa (160 bar) compact cylinders conforming to ISO 6020‑2. The accessories have been designed specifically for use with cylinders manufactured in accordance with ISO 6020‑2, but this does not limit their application[1]. This document covers the following accessories, identified in accordance with ISO 6099: — AP6 — rod eye spherical, female thread (see Figure 1 and Table 1); — AB5 — clevis bracket, spherical eye, in angle (see Figure 2 and Table 2); — AA6-L — pivot pin, spherical bearing, locking plate (see Figure 3 and Table 3); — AL6 — locking plate for pivot pin (see Figure 4 and Table 4); — AP2 — rod clevis, female thread (see Figure 5 and Table 5); — AP4 — rod eye plain, female thread (see Figure 6 and Table 6); — AB2 — eye bracket (see Figure 7 and Table 7); — AB4 — clevis bracket, straight (see Figure 8 and Table 8); — AA4-S — pivot pin, plain (split pins) (see Figure 9 and Table 9); — AA4-R — pivot pin, plain (rings) (see Figure 10 and Table 10); — AT4 — trunnion bracket (see Figure 11 and Table 11). These accessories are used on hydraulic cylinders for mechanically transmitting the cylinder force. The design of these accessories is based on the maximum forces resulting from the specified internal diameters of the cylinders and pressures according to ISO 3320 and ISO 2944. This document only applies to the dimensional criteria of products manufactured in conformity with this document; it does not apply to their functional characteristics. [1] 1 bar = 0,1 MPa = 10 5 Pa; 1 MPa = 1 N/mm 2