残余应力测量方法

[中文适用范围]： 本手册已整理为必须测量残余应力的工程师的现成参考资料。尽管文献中关于残余应力测量的各种方法的信息非常丰富，但本手册的独特之处在于，对大多数有用的方法进行了选择、描述、分类和比较。测量残余应力的方法可分为机械法、物理法或化学法。最广泛使用的机械方法涉及对零件进行机械加工以释放残余应力。这些方法被详细考虑，并占据了本手册的大部分内容。在物理方法中，X射线衍射在解决一些残余应力问题方面具有许多优点。主要优点之一是，如果只需要表面残余应力，它是完全无损的。简要描述该方法并讨论其局限性，以便研究者在满足其需要时可以选择该方法。 [外文原描述]： This manual has been assembled as a ready reference source for the engineer who must measure residual stresses. Although the literature has abundant information on the individual methods of residual stress measurement, this manual is unique in that most of the useful methods have been selected, described, classified, and compared.Methods of measuring residual stress may be classified as mechanical, physical, or chemical. Mechanical methods that are most widely used involve the machining of the part to release the residual stresses. These methods are considered in detail and occupy the bulk of this manual.Of the physical methods, x-ray diffraction has many advantages in solving some residual stress problems. One of the major advantages is that it is completely nondestructive if only surface residual stresses are desired. This method is briefly described and its limitations discussed so that the investigator may choose this method if it fulfills his needs. The method and the necessary techniques have been covered in detail in Ref. 1.Of the chemical methods, the stress corrosion cracking technique seems to be the most useful. This cracking is known to be dependent upon the surface tensile stress level. At present it is only a qualitative measure of the stress, but perhaps at some future date, quantitative chemical methods may be developed.To make residual stress measurements, the engineer must:1Select the most appropriate method.2Completely familiarize himself with the theory behind the method chosen.3Learn the techniques of measurement used by previous investigators.Note that the word "method" is reserved to mean the individual category of stress analysis, and that "technique" applies to the experimental procedure.The choice of the method depends to a large extent upon the geometry of the specimen, the precision desired, the type and location of the stress it is desired to measure, and the equipment available. The numerous mechanical methods available are classified into four groups. These are: the parting-out method, the layer removal method, the boring and turning method, and the hole drilling method. The nonmechanical x-ray method is briefly discussed here for comparison.Once the method has been selected, measurements should not be taken and their values blindly substituted into equations. Each term in the expressions relating the deformation to the residual stress should be completely understood and the sign convention used for these terms should be well known. For this reason, a derivation for each method has been included with the necessary assumptions and limitations. Following a study of these equations, it may be decided whether some automatic or computer technique should be used. In some instances in which a large number of specimens are to be analyzed, the computer technique offers obvious advantages. At this point, it is also necessary to determine the precision with which the stresses are to be determined. This, of course, can be related directly to the precision used in the measurement of the deformation changes and the original dimensions of the specimen itself.The correct choice of the many and varied techniques for measuring dimensional changes used in the determination of residual stress is extremely important if accurate and reproducible data are to be obtained. Machining stress introduced in dissecting must not be larger or more significant than the stress that is to be measured. The techniques used to remove material are numerous, and some of the better currently used techniques are considered. The specific techniques associated with any particular method are included and special fixtures and procedures are described and sample calculations are given.Cross Reference: